FAST SHIPPING - Order today and we'll ship your order by the next business day!   |   Family owned and operated since 1984

(205) 487-8040   |   Email                        
Photo Gallery        
Design Help        
Custom Drapes        
Custom Valances        
Custom Bedding        

Aug 20

Fitted, ruffled tablecloth in gingham

Summertime outdoor dining is the best, but one of the problems with using a tablecloth outdoors is that a little gust of wind can create a big problem. I thought a bright, summery tablecloth would be nice, and that fitting it would make it stay put. I added a little ruffle on the bottom just for fun. Grab some bright-colored outdoor table settings and you’re ready to go!


(Click fabrics for direct links for purchase at Warehouse Fabrics Inc.)

Gingham orange 1"

Gingham orange 1/16"

I had 1.5 yards of each fabric. My table measured 39″ square.

The pattern

Measure your table. I’m giving directions for a square table, but doing a rectangular table just requires you to adjust two sides, which is easy.
Your main table top piece will measure your table length plus 1″ seam allowance in each direction (1/2 inch on either side). For instance, my table is 39″ square, so I cut a piece of fabric 40″x40″. Then cut four side pieces 40″x6″. Finally, cut your ruffle. I cut 5 pieces 40″x2.5″. I serged the bottom of my ruffle instead of hemming it. If you plan to hem yours, you might want to make it 3″ wide instead.

The process

Take your fitted side pieces and sew them together with 1/2 inch seam allowances. Use pinking shears to trim the seam allowances and press them open. Sew them all together so that you have a big loop.
Pin one side at a time to your tablecloth top. You’ll want your seams to be just a little bit away from each edge because we’re going to pivot and sew down the next side.
You’ll use a 1/2 inch seam allowance. Here I’ve sewn down one side and reached the end.
Lift your presser foot and pivot your table cloth. Now the cloth underneath is ready for me to sew down, but the fitted side piece is not yet aligned properly. We need to turn that piece so that the seam that is currently running vertically rotates 90 degrees up to the left.
See? Now I’ve aligned side two of the fitted side with side two of the main cloth. You’ll want your needle to be in the seam while you pivot. Sew this side and repeat all the way around. Unless …
You may get to the end of one of your sides and find you have a bit too much of the fitted side piece. In other words, the seam allowance of the fitted side piece extends too far past the tablecloth piece. This is an easy fix that I do as I go along. Stop a little ways before the end and then place a pin where you’d rather see the seam allowance on the side piece. Sew a new seam on the side piece and trim the seam allowance with pinking shears. Now go back to sewing the way you were before you were so rudely interrupted by your previous sloppiness.
You’ll get a nice fitted edge at each corner.
Now sew your five ruffle strips together into a big loop, ensuring that all raw seams face the same way.
I serged the bottom edge of my ruffle instead of hemming it. If you plan to hem it, do so now.  

NOT PICTURED: Fold your ruffle in half, then in half again. At each fold, make a mark with a fabric marker. This divides it approximately into four sections.

Now do a long gathering stitch along the ruffle, starting a new section with each mark so that in the end, you have four sections you can gather separately. Leave long tails on either end.

Each mark that you made above will correspond with one of the tablecloth corners. Do one side at a time. Pin one mark to each corner. You’ll have a bunch of extra fabric in between, but that’s OK because we’re going to gather it up using the long stitches. Pull the bobbin thread on one end and start gathering it up until it’s about the same length as that side of the tablecloth. Then evenly distribute the gathers and pin in place. 

Sew along that edge, making sure not to go too far and interfere with the gathering stitches on the next side.

Repeat for all sides. This is much easier than trying to gather the whole thing at once and then evenly distribute it around the entire tablecloth.

After my tablecloth was assembled, I went back and serged all of the seam allowances to keep it from unraveling in the washing machine and also to make it look nice.

Other views

(Click for bigger views)

  • VickiT

    Great idea and tutorial. Thank you.

Shoppers are currently looking at:

We welcome you to visit our home store. Enjoy 1/2 price deals and many fabrics you won't find anywhere else! 1726 US Hwy 43; Winfield, AL 35594. Wednesday-Friday 9-5.

Newsletter Signup!

Subscribe to our monthly newsletter to receive Special Sale Notices, Coupons, New Product Info, and More!

Before submitting, be sure to add to your contact list to ensure you receive our mailings.

We never share your information for any reason.


SMS Updates

Text FABRIC to 20566 for SMS Updates

You will receive 3 msgs/mo.Msg&data rates may apply. Text STOP to cancel.

Terms & Conditions